What sets Nostrum apart:
- +51% more flow than a stock LT4 injector / 71% more flow that stock LT1/L86 injector
- Unique 8 hole OEM compatible spray pattern
- 100% of injectors are serialized, tested and batched in a serialized set (+/-3% batching tolerance)
- Direct replacement injectors with no additional accessories needed for install
- 200 bar max recommended operating pressure (rail pressure target)
- Ethanol compatible
- Easy to tune
- Tuning guide and HPTuners (HPT) calibration templates available
Looking to boost your Gen V LT and take it to the absolute limit? You need the all new Nostrum Stage 2 injectors! Our Stage 2 injectors are plug and play and flow a massive 51% more fuel than the stock LT4 injectors – that's enough fuel to support 1400 WHP on gasoline or around 1000 WHP on E85, all without the need for methanol or port injection, or their potentially unreliable controllers!
Our injectors have an OEM equivalent spray pattern with an industry first 8 hole spray pattern, and are fully controllable with the factory engine management. Each serialized injector is individually production tested for gross leak, fine leak (top leak), leak decay (rail pressure test), 3 different static flows, 10 vehicle relevant dynamic flows, maximum opening pressure, maximum flow and then are dynamically batched into sets with very little variance to ensure the best possible experience!
Nostrum backs every part we sell with a limited lifetime warranty. All Nostrum products come complete with everything you need inside the box, including detailed installation instructions. Tuning guides are also available for your dealer or tuner. We have customer service and calibration engineers on staff to provide you with any support that you may need, from installation to tuning.
Application LIst
- 2014-2019 Chevrolet Corvette (C7) including Z06
- 2020-2021 Chevrolet Corvette (C8) - vehicles must confirm not using 6mm stem injectors
- 2014-2023 Chevrolet Silverado/GMC Sierra [2021+ vehicles must confirm not using 6mm stem injectors]
- 2014-2023 Chevrolet Tahoe/Suburban & Cadillac Escalade [2021+ vehicles must confirm not using 6mm stem injectors]
- 2016-2022 Chevrolet Camaro SS
- 2017-2023 Chevrolet Camaro ZL1
- 2016-2019 Cadillac CTS-V
Recommended tuners:
Frequently asked questions:
Q: Why don't I see horsepower gains with just a pump? Which comes first, pump or injectors?
A: Fundamentally we have to look at the entire fueling system and "where" in the rpm range the limits are. DI fuel systems in stock trim are often pump limited at middle rpm (peak torque) and injector limited at high rpm (peak power). This is due to engine speed. HPFPs are mechanically driven pumps (driven by the camshaft pump lobe spinning at ½ crank speed) and are RPM (engine speed) dependent. Many of the quoted flow increases in the aftermarket are purely displacement based comparisons: where by example the big bore pump has a piston diameter X% larger than the "stock" pump or the swept displacement ((3.14*(radius)^2)*(stroke))of the pump Y% larger than the stock pump. The larger displacement of the pump really shines in low rpm, where the fuel injector has plenty of time (crank angle degrees) to inject fuel. As the engines starts to approach peak power the engine speed starts to become quite short and is limiting the injection duration (crank angle degrees) for the injection event (which is another reason why we like to increase fuel pressure up high!).
Q: Why do your numbers say I will make less horsepower on E85 than 93 octane?
A: Great question! The numbers we list in the product descriptions are similar to the numbers a turbo charger lists for air flow. The numbers are the "fuel system capacity to generate power" regardless of the other engine system limitations (air handling, mechanical limitations, knock propensity). Essentially the numbers are calculated assuming "sufficiently large air flow", "sufficiently capable mechanical assemblies" and disregarding knock limits. The equation uses actual observed engine volumetric efficiency (when available from sponsorship vehicles) and fuel capacity (including target pressures) to calculate power. Gasoline has more energy per mass volume than E85. So the higher fuel flow capacity will mathematically generate higher power potential for a gasoline than a high ethanol content fuel. The other variables (air flow, spark, rotating assembly strength, charge cooling, mechanical assembly strength) are highly variable from build to build. This is why we state horsepower capacity for the fuel system – representing the potential of the fuel system if you have all the other aspects of your build addressed!
